Showing posts with label networking. Show all posts
Showing posts with label networking. Show all posts

Sending Data Across a WAN

If the technologies discussed above for data transmission are inadequate, the network administrator can consider using any of the advanced WAN technologies. Some of these technologies are:

X.25 Packet Switching

X.25 is a set of protocols included in a packet-switching network. An X.25 network uses switches, circuits and the available routes for routing at anytime.

Asynchronous Transfer Mode (ATM)

ATM is also an advanced form of packet-switching. It is a broadband method that transmits data in 53-byte cells. Each cell consists of 48 bytes of data and five bytes of header information. Therefore, the packets that are generated are consistent and uniform. ATM can be used with any media.

ATM switches are multiport devices that can act as either hubs or routers. In architectures, such as Ethernet and Token Ring where only one computer at a time may transmit, ATM uses switches as multiplexers to permit several computers to put data on a network.

Note: In asynchronous transmission, data is transmitted as a stream. Each character is converted into a string of bits. Each string is separated from the other strings by a start bit and a stop bit. In this method, there is no device or method to coordinate transmission between the sender and the receiver.

Integrated Services Digital Network (ISDN)

Basic Rate ISDN uses digital transmission that divides its bandwidth into three channels. Two of these transmit data at 64 Kbps, and the third at 16 Kbps. The 64 Kbps channels can carry voice, data or images. The slower 16 Kbps channel carries signaling data.

A computer connected to an ISDN service can use both the 64 Kbps channels to have a 128 Kbps data stream.

Fiber Distributed Data Interface (FDDI)

FDDI is a high-speed token-passing ring network that uses fiber-optic media and was developed for high-end computers.

FDDI uses a dual-ring topology. In this, there are two data streams flowing in opposite directions around two counter-rotating rings. One ring is called the primary ring and the other is called the secondary ring. The secondary ring acts as a backup. Computers may connect to one or both FDDI cables in a ring.

Wide Area Network Transmission

With components such as bridges, routers and communications service providers, local area networks can be connected to create WANs. Communications services make use of the following three types of transmission technologies:

Analog Connectivity

Analog transmission refers to telephone lines used with modems. These can be:

  • Dial-Up Lines - used for infrequent data transmissions.
  • Dedicated Lines - used for frequent and continuous data transmissions. This method provides a ready communication link.

Digital Connectivity

Digital lines provide faster and a more secure transmission as compared to the telephone lines. Digital transmission does not require the use of modems. Following are the different forms of digital lines:

  • DDS (Digital Data Service)
  • T1
  • T3
  • T4
  • Switched 56

DDS sends data through a device called a Channel Service Unit/Data Service Unit (CSU/DSU). This device converts digital signals into a form that is part of the synchronous communications.

Note: With synchronous communication, bits are sent in a timed, controlled fashion. Transmission stops at the end of one frame and starts again with a new one.

T1 and T3 use point-to-point transmission that can transmit voice, data and video signals. T1 offers high data speeds and is the most widely used type of digital line. T3 is the highest capacity leased line service available.

Switched 56 is a digital dial-up service that requires a CSU/DSU to be installed with each computer on the network.

Packet-switching Networks

Packet-switching is a fast and efficient way to transmit data over wide areas. With packet-switching, data is divided into packets of small size and a destination address is attached to each packet. This way each packet can be sent separately over the network. Packets are transmitted along the best route available between the source and the destination.

LAN Expansion

Networks cannot be made larger by simply adding new computers and more cable because each topology has its limits. However, there are certain components which can increase the size of the network within the existing environment. These components are:

Repeaters

A Repeater is a device that regenerates signals so that the signal can travel on additional cable segments. They do not translate or filter data. For a repeater to work, both segments that the repeater joins must have the same media access scheme, protocol and transmission technique.

Repeaters can move packets from one medium to another. Some multiport repeaters can connect different types of media. Repeaters improve performance by dividing the network into segments, thus reducing the number of computers per segment.

Routers

A Router is a device used to connect networks that use different architectures and protocols. They can switch and transfer information packets across multiple networks. This process is called routing. They can determine the best path for sending data and filtering broadcast traffic to the local segment. Routers cannot link to remote computers. They only read addressed network packets. Routers can link segments that use different data packaging and media access schemes.

Bridges

A Bridge is a device that can join two LANs. However, a bridge can also divide an overloaded network into separate networks, reducing the traffic on each segment and making each network more efficient. A bridge can link unlike physical media such as twisted-pair and coaxial Ethernet. It can also link unlike network segments such as Ethernet and Token Ring.

They are also referred to as Media Access Control layer bridges. A Media Access Control layer bridge:

  • Checks the source and destination address of each packet.
  • Creates a routing table.
  • Forwards packets.
Note: A routing table stores the addresses and all the other information necessary to route information from one network to another.

If the destination address is not listed in the routing table, the bridge forwards the packets to all segments.

Multiple bridges can be used to combine several small networks into one large network. A bridge can be installed internally or externally. Bridges are faster than routers because routers perform complex functions on each packet.

The following are the differences between bridges and routers:

  • The bridge only recognizes the addresses of network cards in its own segment. Routers recognize network addresses.
  • A bridge can only recognize one path between networks. A router can search among multiple active paths and determine the best path.
  • The router only works with routable protocols.

Brouters

A Brouter combines the best features of both a bridge and a router. Brouters can:

  • Route routable protocols.
  • Bridge non-routable protocols.

Gateways

Gateways make communication possible between systems that use different communication protocols, data formatting structures, languages and architectures. Gateways repackage data going from one system to another. Gateways are usually dedicated servers on a network and are task-specific.

Network Operating System

A network operating system does everything a stand alone operating system does, and more in a much more complex environment. In addition to the usual lower level computing tasks, a network operating system is responsible for all the following tasks:

  • Directing data traffic through the network
  • Allowing and preventing access to data based on security requirements
  • Preventing access to data files while they are being processed
  • Managing the flow of information between a variety of workstations
  • Managing requests for printer services
  • Managing communication and messages between network users
  • Managing connections between the network and remote sites
  • Make services as transparent as possible to the user

Components of the Network Operating System

There are two main components of the network operating system. They are:

Client Software

In a network environment, when a user initiates a request to use a resource that exists on a server in another part of the network, the request has to be forwarded or redirected to the server with the requested resource. The component of the client software that does this task is the redirector.

Redirector

The redirector may also be referred to as a shell or a requester. It is a small part of the network operating system that:

  • Intercepts requests in the computer.
  • Determines if the requests can be serviced by the local system itself or it needs to be forwarded to the server.

Designators

A designator is an alphabet that is assigned to each network resource. The redirector keeps track of which drive designators are associated with which network resources.

For example, to access a particular shared directory on a remote computer, we can assign a letter of the alphabet, say H, to it. We can then refer to the shared directory on the remote computer as H and the redirector will locate it.

Server Software

Server software makes it possible for users working on other machines to share the server's data and peripherals including shared directories, printers, plotters and disks.

Resource Sharing

The server software not only allows sharing of resources, but also determines the degree of sharing. The degree of sharing includes:

  • Allowing different users different levels of access to the resources. For example, a file server could give read or write or read and write permissions to different users.
  • Coordinating access to the resources to make sure that two users do not use the same resource at the same time.

Managing Users

Network operating systems make it possible for a network administrator to determine who will be able to use the network. The server software can be used to:

  • Create user privileges, which indicates who gets to use the various resources on the network.
  • Validate user names and passwords at the time of logging on.
  • Grant or revoke user privileges on the network.
  • Remove users from the list of users having access to the server.

Network Services

Network services are network operating application programs that run on the network. The network operating system installation program ensures that the user has a minimum of network services installed by default.

Some examples of services installed by the NT operating system, by default are:

  • Alerter service - notifies selected users and computers, of administrative alerts that occur on the computer. As an example, an alerter service could be set to issue alerts whenever the used space of a hard disk exceeds a particular percentage of the total hard disk space.
  • Event log service - records system, security and program events in the event log.
  • Messenger service - sends and receives messages sent by administrators or by the alerter service.
  • Other services such as the telephony service, which is used by programs to make data, fax, voice calls. These services have to be manually started by the user.